1、 The overall dimensions of the whole vehicle shall comply with the provisions of national standards. And according to the approved product drawings and technical documents.
二、外购件、外协件均应有制作厂的产物及格证，并合适相干规范的请求，经打金鱼
出产厂查验及格前方可拆卸。
2、 The purchased parts and outsourcing parts shall be provided with the product qualification certificate of the manufacturer and meet the requirements of relevant standards. They can be assembled after passing the inspection by the mixer manufacturer.
三、打金鱼
的厂定大总品质不得跨越底盘的大许用值，转向轴(轮)载品质和侧倾不变角应合适GB7258的划定。
3、 The total mass of the mixer truck shall not exceed the maximum allowable value of the chassis, and the steering axle (wheel) load mass and roll stability angle shall comply with the provisions of GB7258.
四、焊缝应平均、平直。无漏焊、裂纹、央渣、表面应无毛边，包砂等景象。
4、 The weld shall be even and straight. There should be no welding leakage, crack, central slag, burr on the surface and sand inclusion.
五、一切外露玄色金属表面均应作防锈处置。表面装潢漆应雅观风雅，合适GB7258的划定。
5、 All exposed ferrous metal surfaces shall be rust proof. The exterior decoration paint shall be beautiful and elegant, in accordance with GB7258.
六、从进料到保送卸料终了，许可的永劫候为90mh，且搅拌筒按划定持续运输不大于300转。打金鱼
行驶时，高车速不得跨越如50km/h
6、 The allowable long time from feeding to the completion of conveying and discharging is 90mh, and the continuous transportation of mixing drum is no more than 300 revolutions. When the mixer is running, the high speed shall not exceed 50 km / h
七、装入预拌混凝土在划定的搅动转速和保送时候保送到交贷地点后，泥凝土品质应符国标请求。
7、 After the ready mixed concrete is transported to the delivery place at the specified stirring speed and transportation time, the quality of the mud and concrete shall meet the requirements of the national standard.
八、进料斗出口尺寸不小于历650mm，距空中高度应不大于3.8m。
8、 The size of the inlet hopper outlet shall not be less than 650mm, and the height from the ground shall not be greater than 3.8m.
九、水泥打金鱼
的出料速率不小于0.65m3/min，出料剩余率小于2-5%。打金鱼
的进料速率不小于2.7m3/min
9、 The discharging speed of cement mixer is not less than 0.65m3/min, and the discharge residual rate is less than 2-5%. The feeding speed of mixer truck shall not be less than 2.7m3/min
十、保送应拆卸安稳。各毗连局部部件不应有破坏、变形等景象，不应有上车与底盘偏离本来的安稳拆卸的环境。
10、 The conveying should be installed firmly. All connecting parts shall be free from damage, deformation and other phenomena, and there shall be no deviation between the upper carriage and the chassis from the original fixed device.
十一、车在大总品质状况下，以20km/h的速率府能经由进程14%的坡道外溢。
11、 Under the condition of large total mass, the vehicle can overflow through 14% ramp at the speed of 20km / h.
十二、制念头能府合适国标划定。行驶车外噪声应符国标请求。
12、 The braking performance meets the national standard. The noise outside the vehicle shall meet the requirements of national standard.
十三、整车的各项密封机能杰出，各密封面、管讨论及一切毗连部位均不得有渗油漏气的现 象。
13、 The sealing performance of the whole vehicle is good, and the sealing surface, pipe joint and all connecting parts shall be free of oil and gas leakage.