When we check the concrete mixing plant regularly, we need to check the steel wire rope first. Put a little butter on it for a week to ensure adequate operation. If the steel wire rope is seriously worn, it shall be replaced in time. Check the grease level of the heavy oil pump and replace the grease if necessary. In addition, the water supply system of the concrete mixing plant shall be kept clean at all times to avoid blockage. The suction valve shall be inspected and cleaned regularly.
每一个机电和电气组件的接线不得松动，并且应查抄交换打仗器的打仗器。 混凝土搅拌站配电箱中的尘埃应清算洁净，限位开关不得进入水中。 常常查抄装备，能够随时发明装备的利用毛病，应实时对混凝土搅拌站停止维修和补缀，以耽误其利用寿命。
The wiring of each motor and electrical component shall not be loose, and the contactor of AC contactor shall be checked. The dust in the distribution box of the concrete mixing plant shall be cleaned, and the limit switch shall not enter the water. Check the equipment frequently, and the use failure of the equipment can be found at any time. The concrete mixing plant shall be repaired and repaired in time to prolong its service life.
起首，气体节制体系能够实现便利的输入，便利的操纵，并且能够精确地调剂和点窜每种物料的设定值; 电气节制体系须具备完美的自锁和互锁功效，以确保体系精确，靠得住地运转。 罕见的毛病电气节制体系须具备毛病检测和报警功效。 利用混凝土搅拌
Firstly, the gas control system can realize convenient input and convenient operation, and can accurately adjust and modify the set value of each material; The electrical control system must have perfect self-locking and interlocking functions to ensure the accurate and reliable operation of the system. The common fault electrical control system must have the function of fault detection and alarm. Mixing with concrete
其次，该氛围节制体系在混凝土搅拌站的配料进程中输入为零，从而地节制了计量精度的功效，并设有光报警装配。 有些用户乃至不晓得氛围节制体系的一局部，这并不首要。 现实上，氛围节制体系便是要实现整套装备的主动化。 不氛围节制体系的混凝土搅拌站装备不能一般运转，其首要性很高。
Secondly, the output of the air control system is zero in the batching process of the concrete mixing plant, so as to effectively control the function of measurement accuracy, and a light alarm device is set. Some users don't even know part of the air control system, which is not important. In fact, the air control system is to realize the automation of the whole set of equipment. The equipment of concrete mixing plant without air control system can not operate normally, which is of high importance.
氛围节制体系在混凝土搅拌站中的首要性显而易见。
The importance of air control system in concrete mixing plant is self-evident.
现实上，全部混凝土搅拌站的搅拌体系，骨料体系，保送体系，气体节制体系和节制体系都是首要和必不可少的。 混凝土搅拌站出产线中的中心搅拌仓首要是因为骨料的夹杂效力偶然高于粉末和水的夹杂效力，是以过渡室用于期待粉末和水的配料任务。 罕见于大型搅拌站。
In fact, the mixing system, aggregate system, conveying system, gas control system and control system of the whole concrete mixing plant are important and essential. The intermediate mixing bin in the production line of concrete mixing plant is mainly because the mixing efficiency of aggregate is sometimes higher than that of powder and water, so the transition chamber is used to wait for the mixing of powder and water. Common in large mixing plants.
若是小型搅拌站利用料斗起落机，则现实上不中心皮带仓，骨料能够在晋升的料斗中期待。 同时，因为骨料繁重而轻易健忘的局部将沉入底部。 此时，若是起首插手骨料，则倒霉于混凝土的平均夹杂。 它将耽误夹杂周期并下降夹杂效力。 此时，起首将粉末放入水中。 现实上，与骨料夹杂并搅拌，进步夹杂效力是无益的。
If a hopper elevator is used in a small mixing plant, there is actually no intermediate belt bin, and the aggregate can wait in the lifted hopper. At the same time, the easily forgotten part due to the heavy aggregate will sink to the bottom. At this time, if aggregate is added first, it is not conducive to the uniform mixing of concrete. It will extend the mixing cycle and reduce the mixing efficiency. At this time, first put the powder into water. In fact, it is beneficial to mix and mix with aggregate to improve mixing efficiency.
若是须要掩护，则电动秘密持续运转，并且平常掩护很是首要：电念头在任务时，请注重任务环境，不要太波动，以防止电念头破坏或加速。 利用寿命。 还要查抄表面，电扇是不是一般任务，是不是很是振动，联轴器是不是靠得住，基座是不是按期牢固，轴承是不是一般任务(听声响)和温度是不是一般( 红外温度计))，电流是不是一般(钳型电流表)，并且环绕纠缠的电念头还须查抄碳刷和滑环。 若是一方面存在很是，则须要疾速停止机电维修和处置。 不然，环境严峻后，您将没法处置。。
The motor shall not be damaged during daily operation or continuous maintenance. If it is necessary to slow down the motor, please pay attention to prevent the motor from being damaged. service life. Also check the appearance, whether the fan works normally, whether it vibrates abnormally, whether the coupling is reliable, whether the base is fixed regularly, whether the bearing works normally (listen to the sound) and whether the temperature is normal (infrared thermometer)), whether the current is normal (clamp on ammeter), and check the carbon brush and slip ring of the wound motor. If there are abnormalities on the one hand, the motor needs to be repaired and handled quickly. Otherwise, when the situation is serious, you will not be able to handle it..