1. The driven plate assembly should be kept clean, and the friction plate must be dustproof, dirt proof and oil proof. Before the clutch is assembled on the engine, the surface of the pressure plate and the flywheel should be scrubbed to remove the oil stain, so as to prevent the clutch from slipping. The clutch is generally adjusted before leaving the factory. There is no need to adjust it in use. If it needs to be adjusted, special process tools must be used to adjust it to prevent the pressure plate from tilting.
2. 为了坚持聚散器任务的安稳性，聚散器压盘总成及从动盘总成在出厂之前已停止了均衡，利用中不要随便的拆换整机，聚散器补缀必须拆开时，必然要先做好暗号，补缀后按原暗号装配偏重新均衡。 在策念头上装配或装配聚散器时，必须对角瓜代打紧或抓紧聚散器牢固在飞轮上的螺栓或螺母。
2. In order to maintain the stability of the clutch, the clutch pressure plate assembly and the driven plate assembly have been balanced before leaving the factory. Do not replace the parts at will during use. When the clutch must be disassembled for repair, make marks first, and then assemble according to the original marks, and pay attention to the new balance. When assembling or disassembling the clutch on the engine, the bolts or nuts fixed on the flywheel by the clutch must be tightened or loosened alternately diagonally.
3. 大型混凝土搅拌机装置聚散器时，要用耐温、耐压的光滑油脂恰当的光滑从动盘花键和变速箱1轴花键，保障从动盘在变速箱1轴花键上能自在挪动，可是适量的光滑油会引发磨擦片打滑，以是必然要注重这一点。
3. When installing the clutch of large concrete mixer, the driven plate spline and gearbox 1 shaft spline should be properly lubricated with temperature resistant and pressure resistant lubricating grease to ensure that the driven plate can move freely on the spline of gearbox 1 shaft. However, excessive lubricating oil will cause friction plate to slide, so we must pay attention to this point.
4. 大型混凝土搅拌机装置时必须非常注重，不要毁伤从动盘花键，防止从动盘轴向挪动因毛刺卡滞而不能分手。 必须保障聚散器分手路程合适请求，分手路程过大，轻易使分手杆碰上从动盘带来风险，分手路程太小，将使聚散器不能完全分手。
4. During the installation of large-scale concrete mixer, great attention must be paid not to damage the spline of driven plate, so as to prevent the driven plate from being separated due to burr sticking due to axial movement. It is necessary to ensure that the clutch separation stroke meets the requirements. If the separation stroke is too large, it is easy to make the release rod touch the driven plate, which will bring harm. If the separation stroke is too small, the clutch can not be completely separated.
5. 聚散器处于接合状况时，分手轴承与分手环之间应坚持2-3mm的空隙，如许在磨擦片磨损的环境下就不会毛病压盘压紧磨擦片。磨擦片磨损至划定磨损极限时，应实时改换从动盘总成，以防止聚散器打滑并划伤压盘及飞轮外表。
5. When the clutch is engaged, a clearance of 2-3mm should be maintained between the release bearing and the release ring, so that the pressure plate will not be prevented from pressing the friction plate when the friction plate is worn. When the friction plate is worn to the specified wear limit, the driven plate assembly should be replaced in time to avoid the clutch slipping and scratching the pressure plate and flywheel surface.
6.准确利用，防止支配不妥引发聚散器打滑。在打金鱼
的平常利用中，要注重对聚散器分手支配机构的查抄，实时解除泵及管路的渗漏的毛病，保障聚散器普通任务。
6. Use it correctly to avoid clutch slipping caused by improper operation. In the daily use of the mixer, attention should be paid to the inspection of the clutch release control mechanism, and the leakage fault of the pump and pipeline should be eliminated in time to ensure the normal operation of the clutch.
明天小编给大师先容的是对于注册送200可提现的打鱼
的相干知识，更多的出色内容请点击咱们的网站征询：http://zhaoyanfilter.com咱们后续会有更多的知识为您送上。
Today, I'd like to introduce to you the relevant knowledge about small concrete mixer truck. For more wonderful contents, please click our website: http://zhaoyanfilter.com We will have more knowledge for you.